Drilling Hydraulics

Directional Survey

Drilling Cost

- Option to select “Subsea Stack” or “Surface Stack”

- Option to Select Unit Systems: METRIC, SI, IMPERIAL and MIX

- Selection of units also per parameter

- Printing and attachments with retina display

- Ability to use gestures

Well Control Simulator iPhone | iPad	Drilling Simulator iPhone | iPad	Leak-Off Test Simulator iPhone | iPad
Well Control Methods iPhone | iPad Mac OS X	Kick Tolerance iPhone | iPad Mac OS X	Drilling Hydraulics iPhone | iPad Mac OS X

• Option to select “Subsea Stack” or “Surface Stack”
• Option to Select Unit Systems: METRIC, SI, IMPERIAL and MIX.
• Selection of units also per parameter
• Sharing data files via iCloud ou by email.

New in this update: 

- Ability to import data from apps on iCloud to fill the worksheets:

Well Control Methods iPhone | iPad Mac OS X

Kick Tolerance iPhone | iPad Mac OS X

Drilling Hydraulics iPhone | iPad Mac OS X

and also from apps for iOS (iPhone, iPod Touch and iPad)

Importing data from other apps 

New screenshots:

contact@wellcontrol.com.br

http://www.wellcontrol.com.br

 

New in this update: 

- Ability to import data from apps on iCloud to fill the worksheets:

Importing data from Well Control Simulator 

 

Other screenshots from previous version

contact@wellcontrol.com.br

http://www.wellcontrol.com.br

 

Features: 

Well Control Simulator Provides a graphical very useful tool for training of roughnecks, derrickmen, drillers, tool pushers, drilling engineers and students in the well control procedures.

- Interactive System: no pre-set methods;
- Ability to apply methods: Driller’s method, wait and weight, dynamic volumetric and static volumetric (lubricate and bleed);
- Capacities and Volumes;
- Hydraulics and Hydrostatics and critical pressures calculations;
- Behavior of the kick;
- Applied with subsea stack and surface stack;

Kick Model: 
The model assumes that the kick starts as a single bubble and migrates upward as a single bubble from the bottom to the surface.

Notes: 

Features: 

Well Control Simulator Provides a graphical very useful tool for training of roughnecks, derrickmen, drillers, tool pushers, drilling engineers and students in the well control procedures.
- Interactive System: no pre-set methods;
- Ability to apply methods: Driller’s method, wait and weight, dynamic volumetric and static volumetric (lubricate and bleed);
- Capacities and Volumes;
- Hydraulics and Hydrostatics and critical pressures calculations;
- Behavior of the kick;
- Applied with subsea stack and surface stack;

Kick Model: 
The model assumes that the kick starts as a single bubble and migrates upward as a single bubble from the bottom to the surface.

• For simulation of drilling and kick detection, use another app “Drilling Simulator“.
• For simulation of leak-off test, use another app “Leak-Off Test Simulator“;
• For methods to control, use another app “Well Control Methods“;
• For kick tolerance calculations, use another app “Kick Tolerance“;
• For hydraulic calculations, use another app “Drilling Hydraulics“;

1. Improved Stability;
2. Improved Well Configuration;
3. Improved the work with data files;
4. Added button to reset kick
5. Fix bug to reset fracture

 New screenshots

contact@wellcontrol.com.br

http://www.wellcontrol.com.br

Features: 

1) Panel with the following parameters: pump pressure, mud pump speed, strokes totalizer, flow rate, mud weight, bit depth, rotary speed, hookload and weight on the bit;
2) Instruments with pointers to the parameters: pump pressure, hookload, weight on the bit and rotary torque;
3) Geolograph with parameters: drillpipe pressure, choke pressure, active volume, hookload, weight on the bit, length drilled, flow in, flow out, percent of flow, rotary torque, rotary speed and drilling rate.
4) Panel with alarms: pump failure, vol high, flow high, bop failure, bop status and choke status;
5) Toolbar with buttons: Well Config, Circulation Options, Set Alarms, Graph Limits, X-times faster, Pause/Continue, Restart, Send by email, about;
6) set drillstring with drillpipe1, drillpipe2, heavy-weight, drillcollar1 and drillcollar2;
7) Select floating rig or land rig;
8) Select unit systems: International, field1 (imperial) and field2 (mix);
9) set fluid parameters: mud weight, plastic viscosity, yield point and initial gel;
10) Select rheological models: Power or Bingham;
11) Set gradients: absorption, fracture and temperature;
12) Set jet nozzles or fixed TFA;
13) Set choke parameters and BOP test pressure;
14) Set Surface circulation volume;
15) Set surface circulation equipments (mud pump and lines);
16) Set four formations to drilling (height, pore gradient, fluid density and sof/hard);
17) Save configuration to data files and share by iCloud;
18) Select circulation options: drillpipe -> Riser, Kill -> Riser, and Close BOP;
19) Set alarms: pit gain, flow rate out, max pump pressure and max pump power;
20) Register the kill line losses and pump pressure at the kill speed;
21) show the well with drillstring and the drillbit on rotating;
22) Show schematic of well with drillstring, kick and neutral point (%);
23) Adjust pump speed, weight on the bit and rotary speed to drilling until kick detection;
24) Shut-in the well using hard method;
25) Register shut-in drillpipe pressure (SIDPP) and choke pressure (SICP) and gain volume;
26) behavior of the kick: keeping the well closed and keeping the well opened;
27) Simulations: Drilling, Kick detection, Shut-In, Underground Blowout at shoe and blowout with failure of bop;
28) Capacities and Volumes calculations;
29) Hydrostatic and critical pressures calculations;
30) Hydraulics calculations;
Note: This Drilling Simulator NOT allows to control the well after the kick detection and shut-in. The simulation ends after the simulations of underground blowout and blowout to surface.

Notes: 

New in this update:

The following screenshots were taken on iPod 5th gen (iPhone 5 larger display) 

 Drill, detect kick, close the well and wait for stabilization of the pressures:

 Screenshot in real size on iPod Touch 5th gen (640×1136)

Import by iCloud from the app “Well Control Simulator” to control:

Well Control Simulator for iPhone  (new version 1.2)

Well Control for iPad  (new version 1.2)

Other Screenshots of the Drilling Simulator

Features:

1) Panel with the following parameters: pump pressure, mud pump speed, strokes totalizer, flow rate, mud weight, bit depth, rotary speed, hookload and weight on the bit;
2) Instruments with pointers to the parameters: pump pressure, hookload, weight on the bit and rotary torque;
3) Geolograph with parameters: drillpipe pressure, choke pressure, active volume, hookload, weight on the bit, length drilled, flow in, flow out, percent of flow, rotary torque, rotary speed and drilling rate.
4) Panel with alarms: pump failure, vol high, flow high, bop failure, bop status and choke status;
5) Toolbar with buttons: Well Config, Circulation Options, Set Alarms, Graph Limits, X-times faster, Pause/Continue, Restart, Send by email, about;
6) set drillstring with drillpipe1, drillpipe2, heavy-weight, drillcollar1 and drillcollar2;
7) Select floating rig or land rig;
8) Select unit systems: International, field1 (imperial) and field2 (mix);
9) set fluid parameters: mud weight, plastic viscosity, yield point and initial gel;
10) Select rheological models: Power or Bingham;
11) Set gradients: absorption, fracture and temperature;
12) Set jet nozzles or fixed TFA;
13) Set choke parameters and BOP test pressure;
14) Set Surface circulation volume;
15) Set surface circulation equipments (mud pump and lines);
16) Set four formations to drilling (height, pore gradient, fluid density and sof/hard);
17) Save configuration to data files and share by iCloud;
18) Select circulation options: drillpipe -> Riser, Kill -> Riser, and Close BOP;
19) Set alarms: pit gain, flow rate out, max pump pressure and max pump power;
20) Register the kill line losses and pump pressure at the kill speed;
21) show the well with drillstring and the drillbit on rotating;
22) Show schematic of well with drillstring, kick and neutral point (%);
23) Adjust pump speed, weight on the bit and rotary speed to drilling until kick detection;
24) Shut-in the well using hard method;
25) Register shut-in drillpipe pressure (SIDPP) and choke pressure (SICP) and gain volume;
26) behavior of the kick: keeping the well closed and keeping the well opened;
27) Simulations: Drilling, Kick detection, Shut-In, Underground Blowout at shoe and blowout with failure of bop;
28) Capacities and Volumes calculations;
29) Hydrostatic and critical pressures calculations;
30) Hydraulics calculations;
Note: This Drilling Simulator NOT allows to control the well after the kick detection and shut-in. The simulation ends after the simulations of underground blowout and blowout to surface.

Notes: 

New in this update 1.5: 

• Improved Stability;
• Improved Well Configuration;
• Improved the work with data files;
• Added button to reset kick and fracture

New Screenshots (version 1.5)

Drill, detect kick, close the well and wait for stabilization of the pressures: