Leak-Off Test Simulator for iPhone and iPod Touch 1.0 submitted to the iTunes App Store

Leak-Off Test Simulator for iPhone and iPod Touch 

iLOTSim_512.png Awaiting for Approval by Apple

This app provides a graphical very useful tool for training of Technicians, Drillers, Toolpushers, Drilling Engineers, Students and others professionals of the oil & gas industry to simulate leak-off test.

About the Leak-off Test on drilling operations:
A test to determine the strength or fracture pressure of the open formation, usually conducted immediately after drilling below a new casing shoe.
Initially, pumping fluid into the borehole results in volumetric compression of the drilling mud column and elastic expansion of the casing string plus rock around the borehole. As the pressure in the borehole increases, the leak-off pressure (LOP) is reached when the relationship between pressure increase and volume of fluid pumped deviates from linear. This occurs when fluid begins to diffuse into the formation at a more rapid rate as the rock begins to dilate. Generally, a LOT is a test that finishes immediately after LOP is reached.

Features:

1) Panel with the following parameters: pump pressure, choke pressure, mud pump speed, strokes totalizer, flow rate, mud weight and volume;
2) Intuitive graphical interface: Instruments with pointers to the parameters: pump pressure, choke pressure and open/close hydraulic choke;
3. Graph Options:
– Pressures Pump / Choke and Volume Pumped versus Pumping Time;
– Pressures Pump/ Choke and Pumping Time versus Volume Pumped;
4) Panel with alarms: pump failure, bop failure and bop status;
5) Toolbar with buttons: Data File, Well Config, Restart, Ranges, Set Alarms, Graph Limits, Pause/Continue, Restart, Set BOP, Send by email, about;
6) Set drillstring with drillpipe, heavy-weight, drillcollar1 and drillcollar2;
7) Select floating rig or land rig;
8) Select unit systems: Metric, SI, field1 (imperial) and field2 (mix);
9) set fluid parameters: mud weight, plastic viscosity, yield point and initial gel;
10) Select rheological models: Power or Bingham;
11) Set gradients: absorption and fracture;
12) Set jet nozzles or fixed TFA;
13) Set choke parameters and BOP test pressure;
14) Vertical or Slant Well Type (KOP, TVD and Measured Depth);
15) Set surface circulation equipments (mud pump and lines);
16) Save configuration to data files;
17) Select circulation options: drillpipe -> riser and drillpipe -> choke, Close/Open (Hard shut-in) the well;
18) Reset alarms: pump failure: max pump speed, max pump pressure and max pump power;
19) Register the pressures at the kill speed ;
20) Show schematic of well with drillstring;
21) Shut-in the well using hard method;
22) Circulation on slow rate (kill speed);
23) Useful for filling of Standardized Kill Sheets for Well Control;
24) Useful for Filling of Previous Recorded Sheets;
25) Analyze of the Choke Line effect in Maximum Choke Pressure;
26) Analyze of the Effect of porosity and permeability on absorption curve;
27) Simulation of the Leak-Off Test operation and Graphical Analize of the Leak-Off Test
28) Capacities and Volumes calculations;
29) Hydrostatic and critical pressures calculations;
30) Hydraulics calculations;

Basic Exercise:
1. Close BOP and Choke;
2. Set Mud Pump Speed;
3. Monitor the Choke Pressure;
4. When the pressure deviates from linear, stop the mud pump;
5. Wait until the choke pressure stabilize;
6. Tap on graph to obtain data;
7. Open choke to bleed until choke pressure to zero;

Notes:
1. Set fracture gradient > absorption gradient;
2. The Absorption curve is function of porosity and permeability.
3. Tap with finger and moving it in the graph area to obtain Choke Pressure,
Equivalent Density, Equivalent Gradient, Volume Pumped and Pumping Time.

 iLOTSim_10_01.PNG iLOTSim_10_02.PNG
iLOTSim_10_06.PNG  iLOTSim_10_07.PNG
iLOTSim_10_03.PNG  iLOTSim_10_04.PNG
iLOTSim_10_05.PNG  iLOTSim_10_08.PNG

wellcontrol_url.png

contact@wellcontrol.com.br

http://www.wellcontrol.com.br

Advertisements

Published by

Well Control

We are a team of specialists in petroleum engineering with over 24 years of expertise in oil wells drilling and workover operations. We have in our portfolio Well Control Simulators for training and Monitoring Systems for the oil industry. Our mission is to bring petroleum specialists and students innovative tools which will provide safety and efficiency to their work.

Leave a Reply

Please log in using one of these methods to post your comment:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s